IPG cleanLASER 
Laser Cleaners

German-engineered laser cleaning, powered by IPG fibre lasers. Strip rust, paint, oxides and contamination with no blasting media or chemicals.
Exclusive to Industrial Laser Solutions in Australia & New Zealand.

Send us a sample part

Why IPG cleanLASER?

cleanLASER, based in Herzogenrath, Germany, has been building industrial laser cleaning systems since 1997. It pioneered the technology and has around 2,000 systems installed worldwide across automotive, aerospace, medical, food and heavy industry.

In 2024, cleanLASER became part of IPG Photonics, the world's largest fibre laser manufacturer and cleanLASER's beam source supplier for nearly 25 years. Every system runs an IPG laser source built in Germany.

Industrial Laser Solutions is the exclusive Australian and New Zealand distributor for IPG cleanLASER. You buy direct from the people who install it, train your operators and service it here.

Laser Cleaning vs Traditional Methods


No Media or Chemicals

No blast grit, dry ice or solvents to buy, contain or dispose of. Only easily extracted fume is left.



No Damage to the Part

A non-contact process that removes the coating or contamination, not the substrate underneath.



Selective, No Masking

Target exactly the area you need. Clean a weld zone or strip one section without masking the rest.



Safer for Operators

No silica dust, chemical burns or blasting noise. Laser glasses, gloves and fume extraction do the job.


Discover the IPG cleanLASER Range

Industrial Laser Solutions supplies the full IPG cleanLASER range across Australia and New Zealand, with local installation, operator training and ongoing support. Every system is supplied to Australian power specifications.

Typical applications: weld preparation and post-weld cleaning, rust and oxide removal, paint and coating stripping, mould cleaning, surface pre-treatment and decontamination.

CL 500iM - 500 W Handheld Laser Cleaning System

The new-generation handheld system from cleanLASER. Compact, fully air-cooled and built for daily industrial use, in the factory or out in the field. Its 500 W nanosecond pulsed IPG fibre laser strips rust, paint, oxides and contamination, with up to 30% wall-plug efficiency.

IPG cleanLASER CL 500iM handheld laser cleaner


500 W, Fully Air-Cooled

500 W nanosecond pulsed IPG fibre laser with no chiller to maintain. Up to 30% wall-plug efficiency keeps running costs down.



Built-In Extraction

Fume and dust extraction is integrated into the handpiece optics, with active optics cooling for stable continuous operation.



cleanTOUCH Control

Intuitive touchscreen with preset and saved cleaning programs, plus status lights on all sides showing the operating state.



Tough + Mobile

7 m protected fibre cable, impact-protected chassis, forklift and crane lifting points and braked swivel castors. Runs on single-phase power.


CL 1000 - 1,000 W High-Power Mobile Laser Cleaner

Built for large areas and heavier coatings where throughput matters. The CL 1000 is a robust mobile system for tough industrial use, from large-area paint stripping and mould cleaning to weld seam preparation and derusting.

cleanLASER CL 1000 high-power mobile laser cleaner


1,000 W Laser Power

Diode-pumped beam source for fast removal across large surfaces and heavier coatings.



Real-Time Control

TFT touchscreen displays the laser parameters, with real-time process control.



Process Data Storage

An integrated PC stores your laser process data for repeatable results, job after job.



Remote Diagnostics

Full remote access for maintenance and diagnosis, plus an optional beam switch.


CL 2000 - Up to 1,600 W for Thick Coatings and Large Surfaces

The power-enhanced version of the CL 1000, in the same footprint. Up to 1,600 W of beam source power and a top-hat beam profile make it the choice for heavy decoating and large-area work.

cleanLASER CL 2000 high-power laser cleaner


Up to 1,600 W

The highest power in the range, for thicker layers and larger surfaces.



Top-Hat Beam Profile

Even energy distribution across the beam for consistent, fast decoating.



Same Footprint as CL 1000

More power without a bigger machine. Water-cooled for continuous heavy use.



Made in Germany

Built by cleanLASER on more than 20 years of laser cleaning expertise, with an IPG beam source.









Not Sure It Will Work?
Let's Test Your Part


Tell us what you're cleaning (rust, paint, coating or contamination, and on what material) and roughly how much area you clean per week. Send photos or the part itself, and we'll arrange a test clean with IPG cleanLASER and come back with the results and the right system for the job, at no cost.

Send Us a Sample